Parts & Accessories

Zipp 76/77 Front Hub Endcaps for QR x 100mm Axle

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

- Variable widths - Left: 30.5mm - Center: 52mm - Right: 30.5mm - Length: 113mm - Overall: 134mm

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Thin yellow tape that creates an air tight seal for tubeless applications and can also be used as standard rim tape. - Thin, lightweight tape is designed to provide and airtight seal for tubeless setups - Suitable for use as rim tape in non tubeless application

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.

On today's road forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Converts Mavic road hubs to use 15mm axles - One pair required for each hub to be converted

Industry Nine cartridge bearings are OE replacement bearings. Thickness: 7 Bearing O.D. (mm): 30 Manufacturer Number: 61903 Bearing I.D. (mm): 17

- Rear axle replacement kit, 10mm nutted, DJD-SupaD - Spin Doctor, Spin Doctor Pro and Spin Doctor 6-Drive parts are generally not cross compatible - DJD and DJD-BD parts are generally not cross compatible

ENVE Endcap for Campy 7 -12 Speed Rear Hub

- Extra security against theft - 5mm hex CrMo axle

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 15mm - 1 cone per bag Note: O-ring / seal not included. Check the seal groove closely. This cone has a narrower groove than cone CN-R002. COMPATIBLE HUBS: - 105 FH-5700, 9 speed (right side cone) - 105 SC 1051, 7 Speed Rear - RX100 A551, 8 Speed Rear - RSX 410, 7 Speed Rear - Deore LX M550, 7 Speed Rear - Deore Mtn LX M550, 7 Speed Rear

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 14.8mm - Length: 10.5mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Road 400 CX Front - HB-RM40 Front - Shimano HB-RM40 Front - HB-RA50 Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 14.8mm - Length: 10.6mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Shimano HB-C201 Front - 105 HB-1050 Front - Deore LX/Mtn LX Front - STX HB-MC32/30 Front - Shimano HB-A410, HB-A416 Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - 22mm metal dust seal is pressed on cone - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 15.0mm - Dust Seal Diameter: 22mm - Length: 11.4mm - 1 cone per bag COMPATIBLE HUBS: - Shimano Nexave HB-T400 Front - Shimano Deore HB-M510 Front - STX HB-MC32/30 Front - STX Parallax Front

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech, Joy U, KK 10mm x 1, rear - Compatible with 10mm x 1 axle - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 17.0mm - Length: 13.8mm - 1 cone per bag COMPATIBLE HUBS: - Joytech, Joy U, KK 10mm x 1, rear - Taiwanese rear hubs with 10mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Sovos 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag COMPATIBLE HUBS: - Sovos 9mm x 1, front hub - Taiwanese and similar front hubs with 9mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech, Joy U, KK 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 15mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - JoyTech, Joy U, KK 9mm x 1, front hub - Taiwanese front hubs with 9mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech 9mm x 26, front hub - Compatible with 9mm x 26 axle - Cone Wrench Size: 13mm - Threads: 9mm x 26 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Joytech 9mm x 26, front hub - Taiwanese hubs with 9mm x 26 axle - 105 SC 1055 8-speed Rear - 105 SC 1056 7-speed Rear - XT-II M732 7-speed Rear

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 10mm x 26, rear hub - Compatible with 10mm x 26 axle - Cone Wrench Size: 15mm - Threads: 10mm x 26 - Diameter: 17.0mm - Length: 13.8mm - Note: O-ring / seal not included. - 1 cone per bag COMPATIBLE HUBS: - JoyTech 10mm x 26, rear hub - Taiwanese hubs with 10mm x 26 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 9mm x 1, front "parallax" style hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 11.0mm - 1 cone per bag COMPATIBLE HUBS: - JoyTech 9mm x 1, front "parallax" style hub - Taiwanese hubs with 9mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech, Sovos, KK, KT 9.5mm x 26tpi - Compatible with 9.5mm x 26tpi axle - Cone Wrench Size: 13mm - Threads: 9.5mm x 26 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag COMPATIBLE HUBS: - JoyTech, Sovos, KK, KT 9.5mm x 26tpi - Taiwanese hubs with 9.5mm x 26tpi axle